ATmega128: Unterschied zwischen den Versionen
Aus Nibo Wiki
(→FuseBits) |
(→FuseBits) |
||
| Zeile 36: | Zeile 36: | ||
{| {{BlueTable}} | {| {{BlueTable}} | ||
|Name | |Name | ||
| + | |Bit | ||
|Neuer Chip | |Neuer Chip | ||
|NIBO 2 | |NIBO 2 | ||
|- | |- | ||
|'''EXTENDED''' | |'''EXTENDED''' | ||
| + | | | ||
|'''0xFD''' | |'''0xFD''' | ||
|'''0xFF''' | |'''0xFF''' | ||
|- | |- | ||
|''M103C'' | |''M103C'' | ||
| + | |1 | ||
|0 | |0 | ||
|1 | |1 | ||
|- | |- | ||
|''WDTON'' | |''WDTON'' | ||
| + | |0 | ||
|1 | |1 | ||
|1 | |1 | ||
| Zeile 56: | Zeile 60: | ||
|- | |- | ||
|''OCDEN'' | |''OCDEN'' | ||
| + | |7 | ||
|1 | |1 | ||
|1 | |1 | ||
|- | |- | ||
|''JTAGEN'' | |''JTAGEN'' | ||
| + | |6 | ||
|0 | |0 | ||
|1 | |1 | ||
|- | |- | ||
|''SPIEN'' | |''SPIEN'' | ||
| + | |5 | ||
|0 | |0 | ||
|0 | |0 | ||
|- | |- | ||
|''CKOPT'' | |''CKOPT'' | ||
| + | |4 | ||
|1 | |1 | ||
|0 | |0 | ||
|- | |- | ||
|''EESAVE'' | |''EESAVE'' | ||
| + | |3 | ||
|1 | |1 | ||
|0 | |0 | ||
|- | |- | ||
|''BOOTSZ1'' | |''BOOTSZ1'' | ||
| + | |2 | ||
|0 | |0 | ||
|0 | |0 | ||
|- | |- | ||
|''BOOTSZ0'' | |''BOOTSZ0'' | ||
| + | |1 | ||
|0 | |0 | ||
|0 | |0 | ||
|- | |- | ||
|''BOOTRST'' | |''BOOTRST'' | ||
| + | |0 | ||
|1 | |1 | ||
|1 | |1 | ||
|- | |- | ||
|'''LOW''' | |'''LOW''' | ||
| + | | | ||
|'''0xE1''' | |'''0xE1''' | ||
|'''0xFF''' | |'''0xFF''' | ||
|- | |- | ||
|''BODLEVEL'' | |''BODLEVEL'' | ||
| + | |7 | ||
|1 | |1 | ||
|1 | |1 | ||
|- | |- | ||
|''BODEN'' | |''BODEN'' | ||
| + | |6 | ||
|1 | |1 | ||
|1 | |1 | ||
|- | |- | ||
|''SUT1'' | |''SUT1'' | ||
| + | |5 | ||
|1 | |1 | ||
|1 | |1 | ||
|- | |- | ||
|''SUT0'' | |''SUT0'' | ||
| + | |4 | ||
|0 | |0 | ||
|1 | |1 | ||
|- | |- | ||
|''CKSEL3'' | |''CKSEL3'' | ||
| + | |3 | ||
|0 | |0 | ||
|1 | |1 | ||
|- | |- | ||
|''CKSEL2'' | |''CKSEL2'' | ||
| + | |2 | ||
|0 | |0 | ||
|1 | |1 | ||
|- | |- | ||
|''CKSEL1'' | |''CKSEL1'' | ||
| + | |1 | ||
|0 | |0 | ||
|1 | |1 | ||
|- | |- | ||
|''CKSEL0'' | |''CKSEL0'' | ||
| + | |0 | ||
|1 | |1 | ||
|1 | |1 | ||
Version vom 25. Februar 2011, 16:47 Uhr
Der ATmega128 wird im Roboterbausatz NIBO 2 als Hauptprozessor eingesetzt. Es handelt sich hierbei um einen 8-Bit AVR Mikrocontroller von Atmel mit 128 kByte Flash-Speicher. Da es sich um ein SMD (surface-mounted device) Bauteil handelt, ist der Mikrocontroller im Bausatz bereits auf der Platine aufgelötet.
Technische Daten
| ATmega128 | ATmega128L | |
| FLASH(kBytes) | 128 | 128 |
| EEPROM(kBytes) | 4 | 4 |
| SRAM(kBytes) | 4 | 4 |
| Freq(MHz) | 16 | 8 |
| Spannung(V) | 4,5 - 5,5 | 2,7 - 5,5 |
FuseBits
Die einzelnen Fuse-Bits sind logisch invertiert: 1 (unprogrammed) bedeutet inaktiv, 0 (programmed) beudeutet aktiv.
Beispiel: Der Kompatibiltätsmodus zum veralteten ATmega103 ist aktiv wenn das Bit M103C den Wert 0 hat!
| Name | Bit | Neuer Chip | NIBO 2 |
| EXTENDED | 0xFD | 0xFF | |
| M103C | 1 | 0 | 1 |
| WDTON | 0 | 1 | 1 |
| HIGH | 0x99 | 0xC1 | |
| OCDEN | 7 | 1 | 1 |
| JTAGEN | 6 | 0 | 1 |
| SPIEN | 5 | 0 | 0 |
| CKOPT | 4 | 1 | 0 |
| EESAVE | 3 | 1 | 0 |
| BOOTSZ1 | 2 | 0 | 0 |
| BOOTSZ0 | 1 | 0 | 0 |
| BOOTRST | 0 | 1 | 1 |
| LOW | 0xE1 | 0xFF | |
| BODLEVEL | 7 | 1 | 1 |
| BODEN | 6 | 1 | 1 |
| SUT1 | 5 | 1 | 1 |
| SUT0 | 4 | 0 | 1 |
| CKSEL3 | 3 | 0 | 1 |
| CKSEL2 | 2 | 0 | 1 |
| CKSEL1 | 1 | 0 | 1 |
| CKSEL0 | 0 | 1 | 1 |
Weblinks
- ATmega128 datasheet - Datenblatt über den ATmega128 von Atmel
- avrfreaks.net - Informationen über den ATmega 128 bei AVR Freaks
- www.atmel.com - AVR Webseite von Atmel
